Hi all,

My current coil:
1 ohm and 1.614 mH.

I forgot to mention I had an error with the wire.
I mixed 2 types of wire, wire 1 is 5 layers copper and 3 layers aluminum, wire 2 is 8 layers aluminum.

__________________
Regards
http://Cacharreo.com.es/foro

@torpex

Yes, the 393 comparator's input is from pins 2,6 of 555 and reference voltage for the pulse width pot is from pin 5.

In the video I use plain 5 W car bulb just for testing purposes.
The caps (in total ~126uF 400V DC/AC) around the coil are to create LC tank circuit in my setup.
There are two, identical coils (each is wound bifilar-in-series) facing each other with CW-CCW current flow in bucking magnetic configuration.
Both of them are connected in parallel. lowering the resistance to 1.0 Ohm (0,8 mm wire x 2) with 4,5 mH inductance.
There is a third coil sandwiched in between the two. Its half as wide as a single bifilar-in-series coil and wound with fine 0,3 mm wire bifilarly.

Yesterday I connected my coil and fried my driver chip. There must be something wrongly connected there... have to check it one more time.

So in general the coil is still waiting for treatment

To all,

Dana has brought to my attention that the Voltage Regulator (LM3217) in my combined circuit has a diferent pin out than I drew. This has caused the replication efforts to fail. I will correct this an post it (hopefully today).

My apologies to all who have been affected. I have no explaination why my unit even works, but I must has hooked it up right by mistake. (?)

Bob

Hey kEhYo77,

I must admit again you have a nice set-up...However, I will tell you what I see that I find it will create trouble...

Are this Caps connected to Input (before diodes) or after (Output)?
I believe they should be Non Polarized Caps, or they will allow just one flow according to their hook up, basically if you hook them at Input.

The other thing I particularly do not like about your description above...is that you have wound Two Bifilar Coils in opposite directions (CW & CCW) then hook them in parallel....That creates an Instant Cancellation of both magnetic fields from Coil A (CW) and Coil B (CCW), resulting in a very "Symmetric" Configuration =Zero EM. That is precisely what we are trying to avoid. And that is the reason the Tesla Bifilar Series Configuration as the Patent connection, does NOT work here either...I've tried that already.

According to my tests, all Coils must be wound in the same direction, that includes Secondaries like you have sandwiched between of finer wire...and be careful that secondary will output (depending on # of Turns) a lot of potential (V) and it will definitively Arc...



Regards



Ufopolitics

Hey Bob,

Do not feel bad about it...The LM317 is a resettable transistor...all they have to do is wait til it cools down...or blow it really hard
This are tests experiments, and mistakes are allowed...

Cheers


Ufopolitics

Larry, found that quote at this link:
http://www.frequencyrising.com/FormL...zapper.fax.doc

It is in a document file you have to download. My 2 cents is you would want a 30 khz zapper to do wrist and ankle zapping (switch back and forth) for many hours (some do up to 8 hours straight). Also a 1 khz or 2.5 khz zapper so you can plug in a device called a Zappicator. Dr. Clark developed the Zappicator to treat food. It is also being used to Zappicate the body. The Zappicator penetrates deeper into the body. I recommended this link as they seem to be the most advanced as well as have had the most direct communication with Dr. Clark when she was alive:

The Zappicator | FreeCoil FC8 Super Zappicator

The Dr. Clark protocol involves more than just zapping.

Did you do the different cleanses?

Dr Clark Cleanse Directions

Q: Which cleanse do I do first?
A: Dr. Clark recommended starting with the Digestive Aid Cleanse. It is beneficial to do the Para Cleanse with the Digestive Aid as it will aid in the cleansing process. You can do the Digestive Aid, Para Cleanse, and Kidney at the same time. Just remember that these are very potent herbs. If you begin having difficulties taking them together, slow down and take one at a time.
Q: Can I do the Liver Cleanse first?
A: It is never recommended to do the liver cleanse before completing all 3 of the other cleanses. The reason for this is if you purge the toxins out of your liver and do not have clear channels of elimination, you run the risk of simply re-circulating the toxins. This can make you very ill.

While the Liver Cleanse is the last cleans on this list to do, it does yield the greatest rewards. Personal experience removing thousands of "gall stones". These are not calcified stones but a very hard silly putty like formations. It seems to me as these stones begin to clog the 50,000+ bile ducts many problems begin to form. Over years with reduced or no bile production to assist with the digestion of food many more problems develop. It is amazing the beneficial changes that occur when these stones are removed and the processes are able to perform their functions in a more normal mode.

Also when considering using a Beck device, Dr. Clark strongly recommended to stay away from them because they also use a negative voltage: Parasites can be killed with a very low voltage. But only if the voltage is 100% POSITIVE OFFSET and if the voltage is varied up and down repeatedly. If the varying voltage becomes NEGATIVE, even momentarily, it supports and maintains their lives.

UFO Politics, thanks for allowing these communications.

No survey has been done, but I would suspect that those that do work in the Alternative Energy area are more prone to medical problems as compared to the general population.

IndianaBoys

My pleasure Indiana Boys.
I have also worked on that subject, as putting out Suppressed Cancer Cure Videos...

CANCER CURE SUPPRESSED | Facebook


You Tube suppressed video because of Copyrights...I guess Pink Floyd Money...by EMI...But I love that song and I ain't changing it...


Regards


Ufopolitics

I cured myself of prostate cancer. Shoot me an email and I'll send you a detailed list of what I took and why.

Orion

__________________
Do not be astonished by what you see. Do what we do. Do it! Do it! Do it now!

@Ufopolitics
This is just one of the things I want to try. The fields from both coils do not cancel here, they are in opposition as two separate electromagnets, 'compressing' the space between their facing sides with the same magnetic polarity. It is quite different situation from two windings occupying the same space which are connected in series-canceling way CW/CCW.
There is a spark so there must be is a spike.
Unfortunately I just burnt my last IR2110 driver... I think I'll have to start from scratch with this module. I think the spikes are killing the chip faster then the diodes are able to conduct, although I've got some fast diodes at coil ends STTA512D.
And, YES, I had a load connected - a cap, parallel with my little bulb.
Maybe there is a short circuit on my board or a bad connection or something...
It works great swithing my bulb instead of a coil but with a coil it crashes :/ I have to order now some more ICs...

Hello KEhYo77, I am sorry about your crash, it happened to me once in a shorted coil with a bolt-nut I run to hold caps together, by vibration it rubbed off the enamel coat...and touch just two windings in the start...Mosfet's gone..

Ok, I think I understand now what you are doing...Some kind of Walter Russell arrangement I guess?


Regards and Cheers


Ufopolitics

Hello everybody,

OK. I think we have this thing fixed. Mine worked all along because...I don't know. But it works.

Dana found that I had drawn the pin out wrong in the circuit drawing and I have redrawn it and posted it at the Photobucket site under Bob French's album.

UFO,

I ran a drill motor on the devise yesterday. It ran slow and I didn't turn up the amps much. My MOSFETs got up to 190 degrees and I decided to shut it down. I will need to get more experienced with this and also build a larger devise.

I am building the CF coil, but 3/5ths of my heat shrink tubing is the wrong size. 2/5ths was big enough to use, so I have about 100'-150' of CF "wire" wound so far. I may just go ahead and see what a CF coil this size does. (?)

I also have ordered some 50K tow and 12' of 2" tape. The tape may be great and easy to use. Just wrap a piece of parchment paper to separate the layers. The tape would make a layer 2" wide, like a 2" braided wire of hundreds of thousands of fibers all running parallel (no crossing each other) for the entire coil. What do you think? This would not be like the fabric where it is going across itself, back and forth. Should be more like braided wire. We'll see and I will post everything.

I haven't had time to keep up with all the messages, but has anyone determined just which MOSFET is the best and cheap?

I'm tired, having fun, and very optimistic about the near future of this stuff.

Have fun,

Bob
Have you started the motor's thread yet?