Hi all,

thanx for clarification of green lamp phenomena... I will engage my Samsung Galaxy to see what it can see

Regarding coil:

I have 'regular' enameled wire coil as Ufo suggested, 200+ turns, 20AWG. I do experiments with this coil. But 'resonant' frequency when energy burst comes, is very low, 1kHz and is duty cycle dependent.

Then I was thinking during long nite, and Tesla said, radiant impulse appears in wire in instant moment once switch is closed. Then Ufo announced, that best result he got was parallel bifilar coil. Make sense, two wires, lowed resistance, double radiant generated. And I got idea to employ more than 2 wires at the same time. Recently I have one coil for my solar energy conversion project, to boost poor solar voltage to 400VDC for true sine wave inverter, 500W calculated load. Coil has been designed to do not generate much heat during operation. For this type of coil/transformers I am always using different litz wire (please google it, if you don't know). I just use this coil for test, without ferrite E core of course. Litz wire used is 105 x 40AWG -> total 20AWG -> 1.2mm dia. Coil used is ETD39. So there is 24 turns in 5 layers. Resistance is about 0.5 ohm. 'Resonating' on about 15kHz, which is good for electrolyte caps.

I don't have current measurement, as my meter is showing crap. Needs to buy new one,

@Ufo

I said, light is fully lit with 230VDC on it. Meaning, capacitor bank is holding 230VDC going to the bulb. Driving voltage is 35V.

Of course we can built coil operating on 230V, it must have XL high enough to allow transistor to handle his peak pulse current. But problem will be with pulse amplitude during instant off. It will climb far over Uce or Uds and poor guy will break down. With 200turns and 35V is peak amplitude around 550V, my MOSFET is 600V. I switched to IGBT, because max voltage you can get is 1200V Uce. Much better, no over voltage protection required.

@all

I don't have bigger litz wire available here. Only 20AWG, I bought it on eBay in USA and it takes 2 weeks to arrive here. You are guys in US, you can get thicker litz wire within 2 days. Can you do some tests ??? It would be nice to compare result litz wire / enameled wire. Link is here :

Litz wire 105/40 for Coil and Loop antenna 100' | eBay

this guy got a lot different sizes....

BR

Cinan

Ufo, why you are wasting time with that... Makes no difference, they will always pull the legs... Just leave it... Use this time and do third video instead

Cinan

I expected this kind of response, and alluded to it in my closing statement regarding your needing to be respectful when responding....you weren't.....sad really...

That is exactly why I made the statement. I knew you wouldn't agree with anything I had written. The fact that you find any of it insulting demonstrates that you think you have it all figured out, and external opinions and questions which challenge your authority (in your mind) is unwelcome.

Shoot.

That was two questions......

Your first question it's the exact same question that the learned asks an unlearned when he/she feels that his/her authority is being challenged. If I knew you, do you really think it would change my opinion? I would still challenge your authority!

Your second question is as in a word....terrible...it makes you look bad. I know this much....with reference to your expertise, you praised another individual for providing you with a circuit that you have yet to test (that is an insult, how much effort went into developing that circuit....sad)! I compared the two...your circuit sucks compared to his, that maybe be because electronics isn't your area of expertise...but that's just a guess on my part...
So...it's been established that you may not be an expert in electronics....you say "fields" I haven't seen you do anything that isn't related to electronics so...where is this expertise you speak of, and please elaborate on these fields.

Your forum huh...LOL....This is your thread.....your corner on the forum where you can pretend like you know more than those who pay you a visit in your corner of this forum....LOL.....your forum...you are a funny guy.

Preaching to the choir.....This is your corner of the Forum...your audience..LOL...your believers...(followers). I just made a statement that you didn't agree with......it's you not me who has pages of babble....

I'm not going to be that whipped dog man....bring it...I stated my opinion, one which wasn't welcome. You feel insulted, look in the mirror take it up with that guy staring back at you.

You really think I care about whether you believe me or not? You need believers! You have a few as far as I can tell. I am a fake..you are a fake...we are all fakes...LOL..you think your videos prove anything? There are thousands of individuals making videos and like yours...they prove nothing....

Sure you are glorifying this....it's all radiant this radiant that....blah blah...you got to do it like this..blah..Take some of the advice you keep pouring out, go reread your posts!

Thanks for acknowledging that I know what I'm talking about though, I'm not as smart as you nor do I have your congregation, but I am trying....LOL

Not really difficult to do...John Bedini's pulse motor was put together by a school girl...LOL...she put it together from scratch too...oh wait...you made your own copper wire...molded and made your own magnets....the aluminum you got from bauxit ore, then cast...same goes for the steel I guess...yeah....that changes things....

When you can't beat em,...I wonder....had I not posted that image of my first real pulse motor, what would you have said here? LOL....The image I uploaded is a testament to my attention to detail. I think it's a pretty sweet pulse motor...and you are rattled cause my motor looks better than yours...Plexi-glass makes for exellent demonstration, and proof of concept models....its ignorant to think that you can go straight to the finish line...but you are the expert.....

NO.....I didn't say you need to install neons on your mosfets...you read what you wanted to read.
For the record....All of my circuits are supplied with between 120v-230v.....LOL....soon to increase dramatically....Grow a pair buddy!

I seriously doubt that, but the creator is your judge....Sir...

Till the fundamentals are comprehended, I will stay right here on earth, where its safe.
You have no idea what I mean when I say fundamentals, and that is funny.

uh.....if you say so....

You seriously asking me this? I can provide you with a few quotes where you made an ass out of yourself in the manner in which you responded to a few folks here...but I won't point them out, I will just recommend again that you take some of your own advice, and reread your posts...reread your entire thread! Clean your corner of the forum....LOL......go back and see how you have been treating your congregation.

You have no idea what you are talking about, this is a test model!! You build tiny toys, test them and build tiny toys.... I build large motor/generator test rigs! It's going to be funny watching you eat all this crap you are preaching to those poor unsuspecting individuals, cause you think you know, and the truth is, you aren't even close.

You like that big plastic motor....you don't you...LOL....you like it so much that you make reference to it twice.....she likes you too...LOL.....I'll make you one if you ask nicely.

See you read that one wrong too...you assumed that when "knowledgeable individual" was used, that it was a reference to myself....no buddy, my EGO isn't as inflated as yours...I absolutely loved that post you made in the Ismael Aviso thread where you reveal to all how big your ego really is when you made the highlighed statement.



EGO Alarm bells going crazy...you claim to be one of the few, a member of the club of those skilled in the art....LOL.

I was responding to you when I used the words "knowledgable individual" please don't misunderstand, I would never consider you as being a "knowledagable individual", as you claim to be....I was talking about a real knowledgable individual. You wouldn't know a knowledgable individual if one came up to you and kissed you on the on the mouth, and thats what was ment by my statement.

That is the perfect spot to end this on....

I know who you are now Sir, and what are about!

If it suits you, you can reply to this, but rest assured I will not respond to it, I have said what I want to say, and was civil...LOL



Regards

@erfinder

what the hell is wrong with you ! If you don't have nothing constructive and useful to say, just leave and let this corner as is and go shout your bull**** somewhere else ! If you have problem with the thinks here, don't read it !

I am really tired to find topic related answers hidden between stupid ping-pong posts talking crap. If you have some mental unsolved issues, don't try to fix it here. Nobody is interesting..

Cinan

P.S. don't reply this. I didn't put any question mark, and I don't want to know another piece of your internal mood.

@ufo,

don't be stubborn, do not reply him, do video instead

Hey Buddy,

I agree 100% that so many people are trying to discredit something that is clear to me obtains Radiant energy.
The topic here is to extract more Radiant energy and have a greater understanding of it's relationship to pulse/oscillation circuits.

I have made a few rotored SSG's, SS SSG circuits and finishing my Kromrey Converter to understand this energy more clearly. Ufopolitics circuit has shown the correct properties in his clips to spark my interest in replicating his results and don't care to read this crap.

Looking forward to the third video myself

Regards
Zero

LOL....thats right....come to the aid of your guru.

Cinan,

Thanks for your advice my friend, you are completely and absolutely right.

I will make video instead...

Regards

Ufopolitics

Thanks ZPE

Regards

Ufopolitics

@erfinder, this is a thread started by ufopolitics, if you want to discuss something you think it is interesting to the community, could you please go and start another thread, and stop populating this space with your off-topic ramblings.
We do not want to know your opinion about ufopolitics discovery here, so please, GET LOST.

@arron5120

See thats the problem with you brown nosers...you can't see past what your guru wants you to see, in the information he is providing you with, and his opinions of those who question his information. The thread is interesting, its why I am here. If and when I want to start a thread about something I will, I don't need your permission or invitation to do so. That which you deem to be off topic is right on topic in my opinion, but thats the problem isn't it....opinions aren't welcome! That includes your own! Your praise is desired, your thoughts aren't. It is you and your guru who are rambling, I made a statement which was related to the subject matter, this was interpreted as a personal attack....

We...so you speak for your guru now...LOL...You all should really start thinking, and questioning your leader, his motives, and the more importantly the information that hes giving you.

As far as discovery, please! What discovery.....whats been discovered here....it would be more accurate and gentleman like to say its a rediscovery, and that doesn't apply either! Your leader is "teaching" you that the energy you are playing with is Radiant Energy......its NOT!! If you did your own research instead of waiting for this guy to pave the way for you, you would know that this isn't Radiant Energy!!! Nothing has been discovered! Everyone knows about inductive kickback, and thats what this is! If and when you finally do experience Radiant Energy, your life will change, your circuits will evolve, and you will never look at any of this stuff we do the same way again!!! You aren't anywhere near that.....yet.

Saying please before closing with get lost doesn't make it any less offensive.

I pointed out what I had observed on my bench, thats what researchers do....your guru took offense, his problem, not mine, if I see something that doesn't make sense I will question it......period. The authorities are dead.....and those who took their place are silent!

They have a name for people who don't ask questions and think for themselves........sheep.....

In the 1800s Radiant Energy was defined by authorities, those who had mastered the arts. They identified that it is associated with a "specific" phenomena when caused to manifest in inductors. Contrary to popular belief I have read the material being discussed here, and not once was the mystery phenomena mentioned.

Think for yourselves, you are chasing inductive kickback, you are no where near Radiant Energy.

I have said what I wanted to say, if you don't want me to post again, then don't call me out again!


Regards

Hi Erfinder,
Do you have a link or PDF about this info?

Bert

Edison etheric force ?

Sure I got a list of names, but thats not what you want....If you want to know what Radiant Energy is check out

"Secrets Of Cold War Technology"

Chapter 1.

Radiant Energy for the layman! When you digest that you will have a better and more realistic image of what Radiant Energy really is and be connected back to the guy who more or less "discovered" the force, how he discovered it, and developed a practical application for it after studying it.

Make no mistake, Tesla didn't originate the concept, (Radiant Energy), but he was one of the first (that we can know about) to "master" and tame the force.


Regards

One of the simplest, but precisely defined concepts of Radiant Energy is on Wikipedia:
Radiant energy is the energy of electromagnetic waves.

Before Nikola Tesla times, Maxwell derived and developed two main paths to analyze-calculate Electromagnetism:

1-Symmetrical Systems
2-Asymmetrical Systems

Symmetrical Systems were the ones "legalized and Adopted" by Classic Physics to our date, the ONLY ones we know so far to develop, calculate, design and build must Electrodynamics-Electromagnetic Systems up to now.
Asymmetrical Systems were "Disregarded" by Nobel Prize Scientist Lorentz , financed into this "Enterprise" by John P. Morgan and Thomas Alva Edison.
Heaviside and Johnstone Equations backing Up Maxwell Asymmetrical Systems were also disregarded by Lorentz and Einstein.

The Energy Conservation Laws Applies ONLY to Symmetrical Systems. NOT to Asymmetrical Systems.
The Laws of Thermodynamics also Applies to CLOSED SYMMETRICAL SYSTEMS.

Asymmetrical Systems are based on ELECTROMAGNETIC FEEDBACK, or ELECTROMAGNETIC RESONANCE.

Symmetrical Systems are designed to maintain a Symmetrical Balance between their interactions as to cancel between them, they are CLOSED SYSTEMS. Their Equations "Balances" perfectly, not living space for any "Incoming Force" to develop. They ALL BALANCE OUT by Including a LOSS, whether in Heat or in Parasitical, "Inductive Spikes"...

When applying Symmetry to an Electrodynamic Machine, we have series of shorted interactions, based on closed coils, interconnected between them, either in series or parallel, or combinations thereof.

Nikola Tesla Electrodynamic Machines are MUST based on OPEN COILS PAIRS, OR GROUPS OF PAIRS In their ROTORS, BUT, OPEN, INDEPENDENTLY CONNECTED ONE FROM THE OTHER.
Open, whether interrupted by commutation elements or by Spark Gaps.
This Motors were utilized by Tesla in his Radiant Energy Apparatus...

Asymmetrical Systems includes Capacitors, Transformers, Inductors and Open Coils Motors and Generators, they all violate Lenz Laws and Energy Conservation Laws...just because they are NOT Part, Nor Included in those Laws.

The Tesla Coil, The Don Smith Transformers are examples of ASYMMETRICAL TRANSFORMERS.

If a Motor, every 90 or 180 degrees reverses polarity between its Rotor Coils, cancels its electromagnetic feedback and resonance built up at input timing, creates a heavy electronic and flux collision against the incoming flow, releasing heat and feed-backing High Voltage Spikes, Transient currents and reversed fluxing developing opposite magnetic fields, all known as C or B EMF...
I had developed Motors that do not reverse polarity in order to achieve rotation, they are based on Open Independent or Groups of Coils, Open Systems like Tesla designed back in 1888.
The Coils receives its input, polarizes magnetically and reacts into an attraction-repulsion with the Stators, and then...GO FREE...not colliding against a reversed voltage from another pair of brushes, but delivering to an Output Port its charged current, then traveling "EMPTY" to next Input stage.

Any OPEN, INTERRUPTED COIL after excitation will deliver a free Electromagnetic Feedback, a Magnetic Resonance that will Induce a reversed current of greater magnitude as the Input, and it is understood that if it is NOT DISTURBED by an Incoming reversed voltage/amperage it then CAN THRIVE OUT PEACEFULLY...

That is the Effect that I have on this Open Coil, interrupted by square waves falling to Zero, at Time Off it then travel Free via Diodes towards an Output, sending its reversed generated Voltage/Amperage by Magnetic Feed back to a destination Load.

There is "No Secret" on this...I have written it must on my description on my first post.

According to my tests, this reversed current, obtained by Electromagnetic Feedback reacts-behaves very different than our typical known electricity, and I have proven it through my videos. Even though I have not released all of them because of lack of time...I have to make money to make a living...

Regards to All


Ufopolitics

Torpex,

Thank you for your help. I think that I finally got it.
All my parts are here so I can start to build. I got some Carbon Fiber Tow also and am going to make a coil (I think that I've figured out how to make it...a slow, but doable process.) I'll keep everyone posted.

Thanks,

Bob

Hello Bob,

Can not use Carbon Fiber as a Core or a Spool for your Coil...will kill Radiant flow completely.
I have tested on several cores I have made out of Carbon fibers for different projects...for some reason carbon fibers in the mesh form, create an immediate short circuit of this type of electricity, even isolating it from the enameled wire...it will not thrive.

Regards and good testing

Ufopolitics

UFO,

My 19 AWG quad-filar coil is around a ParCore of 1.5" diameter, 4" outside diameter, and 5.5" tall. It measures 5.3 ohms of resistance. How does this sound? Is the impedance OK? I think that I have the coil direction figured out now thanks to you, Torpex, and Cinan.

I'm using NTE2397 MOSFETs (x4) in your "mine" circuit with the missing wire added. I am replacing the 555 with the LM393 circuit on Page 12, Message #349, and the voltage regulator with the updated version on Page 9, Message #267. Do I need any resistors between the Gate or Source to the LM393 (like you have the 330 ohm resistors from the Gate, and 15k from the Source for the 555)? I assume the 47k resistors from the Gate to the Source are always needed.

I will start testing with neons and CFL. What wattage CFL? I hope I have enough meters.

Can I charge batteries too? If so, what size Ah should I start with? 4Ah, 16Ah, 100 Ah...more? Bedini says that RE doesn't care...put as many as you want, it will just take longer. I've got three 12v, 16Ah batteries to make 36v with. Is that sufficient, and how long will that run for testing? Or does the circuit recharge the Primary? I can't remember. I read the whole thread last week but can't remember everything.

Any suggestions will be most appreciated. Thanks!

Bob

PS - Don't waste your time on those who argue or goad you. Just keep helping those who are friendly and we can all have fun while learning so much great stuff.

UFO,

I was going to coat the fiber and wind it as a coil (instead of copper magnet wire). Are you saying this will not allow RE to flow through the coil?

Bob

Hello Bob,

I hope you've got my message about Carbon Fiber not good for cores-spools.

According to the spec's of your coil it sounds great, the only thing I see is... to be a Quadfilar of 19 awg looks like too much resistance...you've mentioned before around 500 meters right?...that into turns should be a lot...
But it can not harm your system at all, the only inconvenience you may face is that it will spent too fast your batteries for every time you start a test...to "fill" those five hundred meters again...
Normally the Coil should be between 1.5 to 2.5 Ohms...

I have not built the LM393 circuit yet, but I figure the 330 ohms should go there after the 100 Ohms common to all Gates..
Yes, the 47K resistor from gate to ground is your "call back" reset of MOSFET's...the Biasing factor, otherwise they will not turn fully off...and you may play with this values according to your set-up...increasing, but never decreasing this value.
Related to what batteries...I will start with the lowest Ah values...I assume (according to Ah values) they are lead-acid batteries..and not LiPo's?
I have tested with lead-acid, it will work also...but will last less..
No, the system I have not tried to recharge the batteries...I use LiPo's must of times and they last through all my tests just fine..however LiPo's have a very strict rules to be recharged...
It will charge lead acid but with an additional set up...that includes a charger fed by the coil output...but just test it simple set up by now...and tell Us how it went...I am anxious to hear you!

Good testing!!

Ufopolitics

Hello Bob, I am sorry, I misunderstood you...

Using Carbon fiber Mesh to build a Core or a Spool to wind regular magnetic wire will not let RE to show up...I thought you were making a core or a spool out of Carbon fiber...
And now with your last quoted text...I am even more lost and confused...

Ok...If I understand now...are you going to wind carbon fiber strands and coat them with resin instead of regular magnetic wire?
If that is what you are doing you will obtain results here that no one have before...Radiant travels through Carbon Fiber thousands of times faster than Hot electricity...However...I can not tell you if Hot will create a strong magnetic field of enough magnitude as to bring in Radiant field...

I wanted to make that test...but have not been able to find long strands of carbon fiber in spools isolated already...I understand it is used on Heaters Elements applications...but had no luck finding it...

What are you using to isolate it?, it must be a High Temperature resin...and very flexible...
The thing is...Radiant travels so fast on fiber that it shorts out in a mesh, even touching both outputs to a carbon fiber piece made out of cylindrical mesh...Now if it is a long piece or bar made out of carbon mesh...not round or cylindrical, it will spark...but it will not die...interesting Eh?

I have a prior post where I explained my results with carbon fibers...

PD: Make sure there is not even a tiny piece of fiber exposed without insulation...or it will "jump" its Arc somewhere...and short out coil...that could fry your MOSFET's..!!

Regards


Ufopolitics

UFO,

My coil wires are 500 feet, not meters and 5.3 ohms.

The carbon fiber tow I bought is 115 yards of continuos fibers. They are not broken and I have looked at them with a magnifying glass...they seem verysmooth on the outside surface. I plan to wind a coil with this. I think that I can apply a fast drying resin/epoxy/etc. as I wind, with time allowed for drying for each layer. I'llsend you the product designation, cost, and where I got it when I find the invoice. I'm excited to see what it will do.

Good luck, have fun, and keep on truckin',

Bob

Hello Bob,

Wow that is great fiber!, thanks and yes I also want to make that test.
I have carbon fiber but it is a mesh, a fabric, to make racing panels and other app..when I pull one strand it is not a solid piece, but many pieces...so it comes apart very easy...not good for this purposes.
Now, if it is naked fiber , test its continuity outside...and see if it is bare fiber.
If it is, then every layer is going to be making contact between turn levels of the fiber...so you will have a whole layer shorted out.

I recommend you use a fine strip of kind of wax paper -(I use the type used for electric motors isolation between teeth or poles) one end glued to core , and as you wind you cover each turn of fiber with the paper strip. Meaning same you were going to do between layers but doing it between turns...
It is more work, but it will not short out for sure.
Resin is a mess, and you are going to loose that material...it will short out even between resin layers by its arc. Trust me

If it comes already isolated then disregard all the above and good luck and waiting for your results....and yes definitively I want that fiber...I want to wind Motors with it!!

Have a great weekend

Regards

Ufopolitics

Zero,

I've been getting NTE2397s for $5-6 from Newark Electronics/Element 14.

Bob

UFO,

The carbon fiber that I got is called "tow". I got the thinnist they offer which is about 1/32" thick. It is made of 1000 continuous fibers. I got it from: CST Composite Store (800) 338-1278 or cstsales.com.

I bought: 1k Tow, 115 yds. (for $20)

I think you'll like this stuff. Just need to figure out how to insulate it from itself for winding coils. I don't understand your comment that if I epoxy/resin between wires/layers that it will still arc across and short out coil. Why is that?

Enjoy,

Bob

PS -Ignor the disruptors! They don't build, encourage, or help. They only waste everybody's time...words, words, words. Let them start their own thead and watch nobody come to it. They come here because other people come here. People will not go to them, because they area waste of time.

Wrong bud! I most certainly build! Study comes first. I'm wasting my time, not yours. I came here because the thread started off like it was going to go somewhere, but didn't (my opinion, I know you didn't ask for it). Not looking for attention....looking for answers mate. There is only one area...you'll figure that one out soon enough.

I respond to you not because you come at me directly, you come indirect...smooth criminal...

Judge not lest ye be judged.


Regards

Thank you very much Ufopolitics for your always clear and precise explanation of this very interesting phenomenon and above of all for your patience and your "open-source" spirit!

Ciao e grazie ancora da chi capisce poco di queste cose!

Marco

Bob,

Thankyou for the infomation on the MOSFETS. I have an account with RS so I just grabbed the parts with other orders.

However, there is an Element 14 ( previously Farnell ) in Australia and I will have to make a account with them.

I found 30-40 IRF740 MOSFETS in a parts box and made a timer circuit with 2 in parallel to test. Is Mothers Day tomorrow but I hope to make the time to test and post up a clip or pics.

Regards
Zero

Ciao Marco come vai?

Sono bene felice che, almeno ora, capiate un poco più...

il mio piacere

riguardi

Ufopolitics

Thanks Bob, I will definitively get this fiber!!

Ok, if you are just isolating the whole layer, and not turn by turn...it will arc between turns, unless you leave a gap between turns and cover with epoxy, if , let's say two turns of naked fiber, are too close to each others it will count as just one turn...they will short.
Just like winding a coil with bare wire...not insulated...it will short out, will not work.
Hope you understand me now.

I have made several tests with carbon fiber and Radiant...
Radiant reacts to this fiber as a Superconductor for Hot electricity, but even faster.
I am planning to wind a motor with carbon fiber...but to run it with radiant output...not hot.
Just by getting fiber close to a Radiant Spark Gap...it Arcs to the gap...and getting it further out creates effects in the output as to magnify them.
I have build carbon fiber electrodes as spark gap and works better than solid plain carbon brushes, just because it arcs from a bigger gap, and the light is so intense that it will blind you.
I have conducted the Dr Chung/J.L Naudin tests on negative resistor...excellent results, very negative resistance values.
It crashes to the point of having to reset to zero your system in order to get Radiance back, when you just touch a carbon fiber cylinder with your two radiant output terminals.

The only problem I see on Coils is that it offers a lot of resistance to Hot electricity, not to Radiant, however this fact gets your coil very hot...therefore I am not sure if Hot will originate a strong magnetic field needed to bring radiant field in...But trying is the only way to find out...so go for it!!
It will be a new approach...and there is nothing to loose as long as you keep reading the Coil Temperature during test.

Good testing!!

Regards

Ufopolitics